PHOTOREFLECTOR BOUNCE CARD MANUAL
PHOTOREFLECTOR BOUNCE CARD SKIN
PHOTOREFLECTOR BOUNCE CARD FULL
PHOTOREFLECTOR BOUNCE CARD ISO
PHOTOREFLECTOR BOUNCE CARD TV

Don’t restrict your creativity to only white surfaces a yellowish wall will create a warming tone, blueish walls will be reflect a cool tone. I like a clean white bounce surface, glossy is better because it reflects more light. What is the ambient light and what is the bounce surface? I just mentioned ambient light above.įor best results the bounce surface should be 1-2 meters (3-6 feet) from the flash. There should be 2 questions to ask yourself before you put a bounce card on your camera. Sony needs to add a custom minimum shutter speed when using Auto ISO. With rock solid hand holding skills, images at 1/30 or 1/40 sec are possible, beware shutter speeds can drop to impossible levels like 1 or 2 seconds. You can use the Rear or Slow Sync but keep in mind the shutter speeds will be set according to ambient light. The camera will be set to 1/60 sec shutter or faster and blur from handholding won’t be a problem. Should I use the Fill, Rear Curtain or Slow Sync flash setting? The best setting to use for the flash bounce cards is the Fill flash setting. It is easy to experiment and compare the 0 vs. Of course, if you’d like it won’t hurt to try +3 compensation.

PHOTOREFLECTOR BOUNCE CARD FULL

In most cases the small flash will already be firing at full power at the 0 setting unless you have bright ambient light. Should I crank the dial to +3 flash compensation (via Menu setting) when using the flash bounce cards? Cranking the flash compensation up to +3 with the flash bounce card will usually not make a difference.

PHOTOREFLECTOR BOUNCE CARD ISO

Try setting the ISO to 800 and letting the flash do the work. The other extreme is when the ambient light is too dim, if the camera is in AUTO ISO it will respond by increasing ISO to higher levels and the image may be unacceptable. Your camera has a maximum flash sync of 1/160 second, M mode or S mode is needed to control the shutter speed.

Try increasing the shutter speed to darken the ambient light and bring out the flash effect. If you are not getting the side lighting from your flash you had hoped for, the ambient light may be too bright or the ambient light may be directional and fill in the shadow side of the face.

PHOTOREFLECTOR BOUNCE CARD SKIN

I did some touch up processing and used Alien Skin to enhance the contrast and color.Īmbient light matters. It is possible for the ambient light to be too bright or too dim for a good flash bounce image.

The white balance is nearly incandescent, I manually set it to 3400K rather than true incandescent 2850 K. This image was taken with the amber bounce card near a small mirror on the wall. The subject exposed by the amber will be rendered daylight balanced and any background daylight will be rendered cool blue. Check your image data after a few shots.įor the Amber Bounce Card use the “ FLASH” white balance to create a warm toned image. Avoid AUTO white balance, otherwise the Amber warming cast will be “corrected.” The White and Clear card do not create a intentional color cast so it would be ok to use AUTO white balance OR Flash white balance.įor a creative lighting effect use the “ Incandescent” white balance with the Amber Bounce Card. M mode gives you complete control to set the aperture, shutter speed and ISO.įor flash photography ideally you want your camera to shoot around 1/60 second, a wide open aperture and ISO200 – 1200.

PHOTOREFLECTOR BOUNCE CARD MANUAL

However if you want to control the settings use M manual mode. These modes work well if you don’t care to be technical about camera setup. In P, S and A mode your camera chooses what it thinks are the best settings and these settings will work most of the time. This will give you the ability to aim it really easily, just like the polygon plane, but you will never see the bounce card reflections end top-to-bottom.Īdding a gradient to the card will give you more interest to the reflections in the scene, and is a great way to quickly place highlights and reflections exactly where you want them.With the camera in landscape orientation the flash is bounced off the ceiling and gives a softer lighting of the room. Use a circular shape for your bounce cards. The solution is pretty simple, as shown to use by CyBear. Of course you can simply create a reflective bounce card out of a polygon plane, but while aiming the plane, you might find that you will be able to see where the card ends in the animation, depending on the angles.

PHOTOREFLECTOR BOUNCE CARD TV

How you can create a reflection on the screen of a device, like smartphone, tablet or tv screen The problem with that is that it will be really difficult to aim the thing to get the reflections exactly where you want them. You can easily use an IBL or reflected environment that uses and HDR. There are a few ways that you can get that bounce card look in your renders.

Photoreflector bounce card